Roof Flashing: What It Is and Why It Causes Most Leaks

Metal step flashing at the base of a weathered brick chimney on an asphalt shingle roof, with a roll of underlayment
Photo: Robert So on Pexels
Quick answer

Roof flashing is the thin metal (and rubber, at vent pipes) that seals the joints where a roof meets a chimney, wall, skylight, valley or plumbing vent. Shingles shed water well on open slopes, but those joints are where water concentrates and materials move apart, so when flashing corrodes, loosens or relies on caulk instead of proper overlaps, leaks follow.

What is roof flashing?

Roof flashing is the thin sheet metal, usually aluminum, galvanized steel or copper, that seals the joints where your roof meets something else. Shingles protect the open slope; flashing protects every place the slope is interrupted.

Those interruptions are everywhere on a typical house: a chimney, a dormer wall, a skylight, a plumbing vent, the valley where two roof planes meet, the edge of the roof itself. Each one gets its own type of flashing:

  • Step flashing: small L-shaped pieces woven in with each course of shingles where a roof runs up against a sidewall, such as a dormer or a second-story wall.
  • Counterflashing: metal set into the masonry or wall above the step flashing and folded down over it, so water running down the wall cannot get behind.
  • Chimney flashing: a combination of an apron on the downhill face, step and counterflashing on the sides, and a back pan or cricket on the uphill side to split water around the chimney.
  • Valley flashing: metal or ice-and-water membrane lining the inside corner where two slopes meet and carry a lot of water.
  • Pipe boots and vent collars: a rubber or metal collar that seals around plumbing vents and exhaust pipes.
  • Drip edge and kickout flashing: drip edge keeps water off the fascia at the roof edge; a kickout diverter at the bottom of a roof-to-wall joint steers water into the gutter instead of down the siding.

Good flashing does not rely on glue. It works by overlapping, like shingles do, so gravity always carries water over the top of the next layer rather than behind it.

Why does flashing cause most roof leaks?

Because flashing sits exactly where water concentrates and where different materials move against each other. In our experience, when a Long Island roof leaks and the shingles still look sound, failed flashing is the usual cause.

An open field of shingles is simple: water lands, runs downhill and drops into the gutter. A chimney or a wall changes that. Water piles up against the uphill side, runs along the joint and looks for any gap. Several things make those gaps appear over time:

  • Movement. A brick chimney, a wood-framed wall and a roof deck all expand, contract and settle at different rates. Flashing has to bridge that movement every season.
  • Sealant doing a flashing job. Caulk and roofing cement dry out, shrink and crack in sun and cold. When a joint depends on a bead of sealant instead of overlapping metal, it is only a matter of time.
  • Old flashing reused. If a previous roofer left the original flashing in place and shingled up to it, the metal may already have been near the end of its life.
  • Missing pieces. Step flashing that was never installed, a chimney with no cricket, or a roof-to-wall joint with no kickout are common on older homes.
  • Rubber aging out. Pipe boots are often the first part of a roof to fail because the rubber collar cracks in UV light long before the shingles around it wear out.

The frustrating part is that a flashing leak rarely shows up where the flashing is. Water gets in at the joint, runs along a rafter or the top of a wall and appears as a stain several feet away. That is why patching the stain, or the shingles directly above it, so often fails.

Where does flashing fail on Long Island and Queens homes?

Chimneys, dormer and second-story sidewalls, plumbing vents and valleys account for most of the flashing problems we see. Local weather and housing stock both play a part.

The house itself

Older Cape Cods often have shed or gable dormers with long sidewall joints and a masonry chimney, which means a lot of step flashing and counterflashing in one roof. Split-levels have several roof sections meeting walls at different heights, so they have more roof-to-wall joints than most styles. Ranches and colonials that gained a second-floor addition frequently have a joint where new framing meets an old roof, and that transition is a classic leak point if it was not flashed carefully.

The weather

  • Nor'easters bring wind-driven rain that pushes water sideways and even uphill under flashing that sheds normal rain without trouble. A leak that only appears in storms from one direction often points to flashing on that side of the house.
  • Freeze-thaw cycles work water into small gaps in mortar joints and sealant, then widen them as it freezes. Chimney counterflashing set into crumbling mortar is especially vulnerable.
  • Ice dams at the eaves can back water up under the lower edge of the roof and into step flashing at walls near the gutter line.
  • Salt air in South Shore communities such as Long Beach, Freeport and Bay Shore speeds up corrosion of thin metal and fasteners, so flashing near the water can wear faster than the same flashing inland.

How can you tell if flashing is causing your leak?

Look at where and when the leak appears. A stain near a chimney, a dormer, an exterior wall or under a vent pipe, especially one that shows up in heavy or windy rain but not in a light drizzle, points strongly toward flashing.

Common clues include:

  • Water stains on the ceiling or upper wall close to where the chimney or a dormer sits on the roof.
  • Peeling paint, bubbling drywall or a musty smell on an interior wall directly below a roof-to-wall joint.
  • Staining or rot on the siding or trim below the lower end of a roof-to-wall joint, a sign of a missing kickout.
  • Visible gobs of tar or caulk around the chimney or vent pipes, which usually means someone has already tried to patch a flashing problem.
  • Bent, lifted or rusted metal, or counterflashing that has pulled out of the brick.
  • A cracked or split rubber collar around a plumbing vent.
  • Leaks that come and go with wind direction rather than with every rain.

None of these proves the cause on its own. Water travels, so a stain can be several feet from the real entry point. Tracing it back is the first step of any honest roof repair.

What can you check yourself, and what needs a pro?

You can do a useful first look from the ground and from inside the house. Anything that involves getting on the roof should be left to a professional.

Safe DIY checks:

  1. Walk around the house with binoculars and look at the chimney, dormers, skylights and vent pipes. Note anything bent, rusty, missing or smeared with tar.
  2. After a rain, check ceilings, closet ceilings and upper walls near those features for fresh stains or damp spots. Take dated photos so you can see whether a stain is growing.
  3. Look at the siding and trim where a lower roof meets a wall. Streaks, swelling or soft wood there are worth mentioning to your roofer.
  4. Note the weather when a leak appears: steady rain, wind from a certain direction, or melting snow. That detail helps narrow down the cause.

Leave to a pro: climbing onto the roof, pulling up shingles, and anything involving the chimney or caulk. Roofs are slippery and steep, and a well-meaning bead of sealant on top of failed flashing often traps water and makes the real problem harder to find later. A roof inspection with photos lets you see exactly what the roofer sees.

How should flashing be repaired?

Properly repaired flashing is replaced with new metal installed in overlapping layers, not covered with sealant. That usually means lifting or removing the shingles around the joint, taking out the old flashing and rebuilding the detail.

What that looks like depends on the location:

  • Sidewalls and dormers: new step flashing installed one piece per shingle course, tucked behind the siding or wall covering, with ice-and-water membrane underneath where it makes sense.
  • Chimneys: a new apron, step flashing and back pan or cricket, with counterflashing set into a cut joint in the mortar rather than glued to the face of the brick.
  • Vent pipes: a new pipe boot or vent collar woven into the shingles so the upper shingles overlap it.
  • Valleys: old shingles and membrane removed and the valley relined and reshingled.
  • Roof-to-wall joints near the gutter: a kickout added so water lands in the gutter instead of behind the siding.

Manufacturer installation instructions for asphalt shingles call for these flashing details, and the Asphalt Roofing Manufacturers Association publishes guidance on how shingle roofs should be flashed. Matching shingles are used where we can find them, and the repair is photographed before and after.

When a flashing leak means a bigger job

If the roof is near the end of its life, has leaks at several joints, or the decking under a failed joint has rotted, rebuilding one detail may not be the best use of your money. In that case a roof replacement replaces all of the flashing at once as part of the new roof system. A good roofer will tell you plainly which situation you are in.

Can flashing problems be prevented?

Not entirely, because metal and rubber age no matter what, but most flashing leaks give early warning signs that a regular check will catch.

  • Have the roof looked at after a major nor'easter or a hard winter, when wind-driven rain and freeze-thaw cycles do the most damage.
  • Keep gutters and valleys clear so water and ice do not back up against flashing at the eaves and inside corners.
  • Ask about the chimney's mortar. Crumbling joints let counterflashing work loose, so masonry and flashing should be looked at together.
  • Replace pipe boots when they start to crack rather than waiting for a stain.
  • When you replace your roof, make sure the quote includes new flashing throughout rather than reusing the old metal.

Scheduled roof maintenance covers flashing and pipe boot checks as part of every visit. If you suspect a flashing leak now, LaRocco Roofing & Siding offers a free inspection with a photo report anywhere on Long Island & Queens, NY. Call (516) 924-2050 to set one up.

Related service: Roof Repair

FAQ

Common questions

Can I just caulk around my flashing to stop a leak?

Caulk can slow a leak for a short time, but it is not a repair. Sealant dries out and cracks in sun and cold, and a bead applied over failed flashing can trap water and hide the real entry point. The lasting fix is new metal installed so each layer overlaps the one below it.

Should flashing be replaced when I get a new roof?

Yes, in almost every case. Old flashing has been through the same years of weather as the old shingles, and reusing it can lead to leaks on a brand new roof. Check that your written estimate lists new flashing throughout, including chimney, sidewall, valley and pipe boots.

What is kickout flashing and does my house need it?

A kickout is a small angled piece of flashing at the bottom of a roof-to-wall joint, where a lower roof ends against a wall. It steers water into the gutter instead of letting it run down behind the siding. If you see staining, swelling or rot on the siding just below where a roof meets a wall, a missing kickout is a likely cause.

Can a flashing leak be fixed without replacing the whole roof?

Usually, yes. A roofer lifts or removes the shingles around the problem joint, replaces the flashing and reinstalls or replaces those shingles. A full replacement only makes sense when the roof is near the end of its life, has failures in several places, or has rotted decking that needs broader work.

Does homeowners insurance cover a flashing leak?

It depends on your policy and on the cause. Policies generally treat sudden storm damage differently from gradual wear and aging, which many exclude. Read your policy, call your agent or insurer with questions, and keep dated photos of the damage and any repairs.

Free estimate

Get a free roof inspection and a straight answer

No charge, no obligation, no high-pressure pitch. We look at the roof, send you the photos and tell you what it actually needs.

Long Island & Queens, NY · Financing available

Call Now Free Estimate